![\"orangerx-pinout\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/02\/orangerx-pinout.png\")
<\/a><\/p>\nHow to improve the range?<\/h2>\n
Some points to check to improve your range :<\/p>\n
Replace the UFL (coax cable) of OrangeRX 1W TX modules<\/strong><\/h3>\nJust do it, the provided cables have very often issues (open or short circuit), sometimes immediately and sometimes after several manipulations.<\/p>\n
Always replace them by another one, such as this one<\/a>. One side is a “U.FL” connector<\/a>, the other side is a SMA connector.
\n![\"ori-adaptateur-ufl-sma-20893[1]\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/12\/ori-adaptateur-ufl-sma-208931.jpg\")
<\/a><\/p>\nSolder directly to the RFM23BP module pins<\/h3>\n
Not mandatory, but can avoid unwanted disconnection of the UFL connector.<\/p>\n
Like this :<\/p>\n
![\"antenne_03\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/05\/antenne_03.png\")
<\/a><\/p>\nOr like user “salience” from rcgroups.com :<\/p>\n
![\"coaxjob\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/06\/coaxjob-718x1024.jpg\")
<\/a><\/p>\nUse a thicker coax cable<\/h3>\n
Not mandatory, but if you want to place your antenna a bit further (on the car roof for example), consider using a good and thicker 50 ohms coax cable (RG-58<\/a>), such as this one :<\/p>\n![\"rg58\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/05\/rg58.png\")
Choose good antennas<\/strong><\/h3>\n\n- The stock antennas of OrangeRX modules seem to be 2.4GHz antennas, and will provide a very low range of a few hundred meters.<\/li>\n
- Don’t use monopole antennas !<\/strong> Dipoles are usually sufficient, but some users use other antennas such as yagi, patch, moxon, ground plane, etc<\/a>. 3)<\/li>\n
- Avoid interference sources. Two users who were using bluetooth modules inside or next to the OrangeRX modules have reported lost packets at short range.<\/li>\n
- Have a look here<\/a> for antennas suggestions<\/li>\n<\/ul>\n
How to increase the power ?<\/h2>\n
The out-of-the-box power of the “1W” OrangeRX is around 400mW. However their RF module can really achieve 1000mW, with a simple modification described on this page<\/a>.<\/p>\nHow to activate the brown-out detector ?<\/h2>\n
Please see this page<\/a> for information about the brown-out detector on the OrangeRX modules.<\/p>\nOther issues<\/h2>\n
RF connector shorting the RFM module pins<\/strong><\/p>\nA the connector can rotate, it will easily come in contact with the pins, in particular the first one and that’s problematic : The external part of the RF connector is GND, and when it touches the first pin of the module it shortcuts the antenna. It can damage the module, but usually it will survive a short contact. Maybe this can cause a sudden voltage drop and reset of the atmega too. The photos are from two different brand new modules, first opening. Notice that touching the second pin is not an issue, but touching the first (in the corner of the RFM module) is short circuiting the antenna output. On these two modules it seems that the RF connector is on the second pin, but it’s freely rotating and can touch the first one too.<\/p>\n
![\"DSC_6540\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/10\/DSC_65401.png\")
<\/a><\/p>\nAn option is to use hot glu, another is to cover the RFM23BP pins with tape:<\/p>\n
![\"DSC_6535\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/10\/DSC_6535.png\")
<\/a>
\n<\/a>
\n![\"DSC_6745\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/05\/DSC_6745-1024x682.jpg\")
<\/a> 2) It also happened that the vibrations (quadcopter) broke on pin of the voltage regulator (see comment below)<\/p>\nHow to access the serial port ?<\/h2>\n
7The serial port is not accessible by default, and requires to cut a hole into the plastic :
\n<\/a> ![\"DSC_6743\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/05\/DSC_6743-1024x682.jpg\")
<\/a> ![\"DSC_6747\"](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/05\/DSC_6747-1024x682.jpg\")
<\/a><\/p>\n<\/a><\/h3>\nRemark about the pins RX_ON, TX_ON, RX_ANT, TX_ANT<\/h2>\n
Just for information for people building their own modules, several users are asking if these pins must be connected differently on the 1W and 100mW modules :<\/p>\n
The pins RX_ON<\/span><\/strong> and TX_ON<\/span><\/strong> on the RFM23BP (1W module) are named differently : RX_ANT<\/span><\/strong> and TX_ANT<\/span><\/strong> on the RFM22B (100mW module), and are reversed<\/strong>.<\/p>\nBut their signals are inverted too<\/strong> :<\/p>\n\n- rfm22b<\/b> datasheet<\/a>:<\/li>\n<\/ul>\n
\n
<\/a><\/p>\nSolder directly to the RFM23BP module pins<\/h3>\n
Not mandatory, but can avoid unwanted disconnection of the UFL connector.<\/p>\n
Like this :<\/p>\n
Or like user “salience” from rcgroups.com :<\/p>\n Not mandatory, but if you want to place your antenna a bit further (on the car roof for example), consider using a good and thicker 50 ohms coax cable (RG-58<\/a>), such as this one :<\/p>\n The out-of-the-box power of the “1W” OrangeRX is around 400mW. However their RF module can really achieve 1000mW, with a simple modification described on this page<\/a>.<\/p>\n Please see this page<\/a> for information about the brown-out detector on the OrangeRX modules.<\/p>\n RF connector shorting the RFM module pins<\/strong><\/p>\n A the connector can rotate, it will easily come in contact with the pins, in particular the first one and that’s problematic : The external part of the RF connector is GND, and when it touches the first pin of the module it shortcuts the antenna. It can damage the module, but usually it will survive a short contact. Maybe this can cause a sudden voltage drop and reset of the atmega too. The photos are from two different brand new modules, first opening. Notice that touching the second pin is not an issue, but touching the first (in the corner of the RFM module) is short circuiting the antenna output. On these two modules it seems that the RF connector is on the second pin, but it’s freely rotating and can touch the first one too.<\/p>\n An option is to use hot glu, another is to cover the RFM23BP pins with tape:<\/p>\n 7The serial port is not accessible by default, and requires to cut a hole into the plastic : Just for information for people building their own modules, several users are asking if these pins must be connected differently on the 1W and 100mW modules :<\/p>\n The pins RX_ON<\/span><\/strong> and TX_ON<\/span><\/strong> on the RFM23BP (1W module) are named differently : RX_ANT<\/span><\/strong> and TX_ANT<\/span><\/strong> on the RFM22B (100mW module), and are reversed<\/strong>.<\/p>\n But their signals are inverted too<\/strong> :<\/p>\n<\/a><\/p>\n<\/a><\/p>\nUse a thicker coax cable<\/h3>\n
Choose good antennas<\/strong><\/h3>\n\n
How to increase the power ?<\/h2>\n
How to activate the brown-out detector ?<\/h2>\n
Other issues<\/h2>\n
<\/a><\/p>\n<\/a>
\n<\/a>
\n<\/a> 2) It also happened that the vibrations (quadcopter) broke on pin of the voltage regulator (see comment below)<\/p>\nHow to access the serial port ?<\/h2>\n
\n<\/a> <\/a> <\/a><\/p>\n<\/a><\/h3>\n
Remark about the pins RX_ON, TX_ON, RX_ANT, TX_ANT<\/h2>\n
\n
![\n<\/a>\n](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/10\/DSC_6744.png\"){kind=link}
![\n<\/a>](\"https:\/\/www.itluxembourg.lu\/site\/wp-content\/uploads\/2015\/05\/DSC_6741.jpg\"){kind=link}